Hi Ceflar,
you and bobc make a great job. Thank you to help to develop the Arduino/32-bit Electronic for the reprap.
Duet and smothieboard are also fine Arduino/32-bit Solution, but static or not enough posibillities.
I would like to work with UDOO-Quad, so only with RAMPS-FD and RADDS I have today the posibillity.
I think, that we are pioneers, and in 2-3 years 32-bit becomes a Standard for reprap or 3dprinter Electronic.
The new RAMPS-FD features looks fantastic.
The security Feature are very great for RAMPS-FD.
If you make some prototypes for RAMPS-FD v3 I would like to buy and Test it.
So I can speak directly with "repetier" to add it without errors in the repetier-firmware distribution.
"repetier" and I never has touch or seen a RAMPS-FD :-(
We use now only Watchdog for RADDS (it is working good now, thank you xnaron, vincent, martin and "repetier")...
If only the Arduino Due is broken by the RADDS, the possibility, that the Hotend /heatbad etc... becomes hotter and hotter is high.
Also if we have a new Arduino Due with the standard "Blinker" Firmware (GND, PIN13) and we put the RADDS and give them 12/24 Volt Power,
Imeadiatly the Hotend begin to become wormer and wormer. Maybe you can look for FAMPS-FD v3 to check the PIN13, please.
A drive transistor Regulator is also a good feature for RAMPS-FD. If i give RADDS 24 Volt, I have only the possibility to give the l12 Volt fan-out on repetier-firmware...
#define EXT0_EXTRUDER_COOLER_SPEED 100 // to ca. 80%. max 128 not 255
It is work, but not the finest solution for that ...
In the RADDS v1.2 we have modifications like a dc-dc for 12-29 Volt and on the backside we put 6 x 3SMD-Switch to have the possibility to change the Microsteppingrate,
without to breake the "Electronic- lines" like RADDS v1.1 etc..
The first RADDS v1.2 prototype test it is going not so good.
Now we make a optimisation and we hope to get a good RADDS v1.2 at the end of the year ...
It would also be a little bit expensiver :-(
By the Way, If someone like aditional Features that make sense, please write us via PM.
By the way, I am looking for an Reseller for the US Market.
Less then 1 KG (1 or 2 RADDS) I can send it for 15 Euro ( Maxibrief + Einschreiben without Tracking-ID).
For the Logic, the most US Citizen like the Set = 1xRADDSLCD+RADDS+4x1/128 Microstepperdriver+3xHall-O Endstops (5-3,3 Volt) and sometimes the Extension Board for the Kraken Hotend,
so we get a very high Shipping Rate and it will be more of one Week for delivering Time.
[e3d-online.com]
I would like to get only resellers, that have a deep Knowledge for 3D-Printing.
So we have the Posibility to make a very good Support for the us-reprapers.
[max3dshop.org]
(If eveyone look writing errors, I say Thank you in advance to reporting it via PM).
Can some reprap-dealer help us?
Thank you
Angelo
you and bobc make a great job. Thank you to help to develop the Arduino/32-bit Electronic for the reprap.
Duet and smothieboard are also fine Arduino/32-bit Solution, but static or not enough posibillities.
I would like to work with UDOO-Quad, so only with RAMPS-FD and RADDS I have today the posibillity.
I think, that we are pioneers, and in 2-3 years 32-bit becomes a Standard for reprap or 3dprinter Electronic.
The new RAMPS-FD features looks fantastic.
The security Feature are very great for RAMPS-FD.
If you make some prototypes for RAMPS-FD v3 I would like to buy and Test it.
So I can speak directly with "repetier" to add it without errors in the repetier-firmware distribution.
"repetier" and I never has touch or seen a RAMPS-FD :-(
We use now only Watchdog for RADDS (it is working good now, thank you xnaron, vincent, martin and "repetier")...
If only the Arduino Due is broken by the RADDS, the possibility, that the Hotend /heatbad etc... becomes hotter and hotter is high.
Also if we have a new Arduino Due with the standard "Blinker" Firmware (GND, PIN13) and we put the RADDS and give them 12/24 Volt Power,
Imeadiatly the Hotend begin to become wormer and wormer. Maybe you can look for FAMPS-FD v3 to check the PIN13, please.
A drive transistor Regulator is also a good feature for RAMPS-FD. If i give RADDS 24 Volt, I have only the possibility to give the l12 Volt fan-out on repetier-firmware...
#define EXT0_EXTRUDER_COOLER_SPEED 100 // to ca. 80%. max 128 not 255
It is work, but not the finest solution for that ...
In the RADDS v1.2 we have modifications like a dc-dc for 12-29 Volt and on the backside we put 6 x 3SMD-Switch to have the possibility to change the Microsteppingrate,
without to breake the "Electronic- lines" like RADDS v1.1 etc..
The first RADDS v1.2 prototype test it is going not so good.
Now we make a optimisation and we hope to get a good RADDS v1.2 at the end of the year ...
It would also be a little bit expensiver :-(
By the Way, If someone like aditional Features that make sense, please write us via PM.
By the way, I am looking for an Reseller for the US Market.
Less then 1 KG (1 or 2 RADDS) I can send it for 15 Euro ( Maxibrief + Einschreiben without Tracking-ID).
For the Logic, the most US Citizen like the Set = 1xRADDSLCD+RADDS+4x1/128 Microstepperdriver+3xHall-O Endstops (5-3,3 Volt) and sometimes the Extension Board for the Kraken Hotend,
so we get a very high Shipping Rate and it will be more of one Week for delivering Time.
[e3d-online.com]
I would like to get only resellers, that have a deep Knowledge for 3D-Printing.
So we have the Posibility to make a very good Support for the us-reprapers.
[max3dshop.org]
(If eveyone look writing errors, I say Thank you in advance to reporting it via PM).
Can some reprap-dealer help us?
Thank you
Angelo