Hi again,
I like to test Bobc `s RAMPS-FD.
With the cool securityfeatures (thank you Cefiar) and maybe an EEPROM on board
(I have heared that it is an EEPROM now on the newer RAMPS-FD, right ?).
That can be Important for my target electronic-Setup.
@dc42 Duett, Azteeg X5 mini 32BIT All-in-one Controller and Smoothieboard are, so I think, very cool Boards, but for personaly for me not so Important.
First I would like to work with Repetier-firmware (v 0.92 now realy stable with Due and 1/128) because repetier is a friend of my and so I have so a PREMIUM SUPPORT :-).
At Least I will run also my Printes with a UDOO Quad board (not with a Arduino Due).
Then I will run with 1/128 Microstepper and 2-3 Hotend-extruders and one silence permanent fan for the Metall Hotend and a second for individual Filamentcooling.
Also I am a friend, that I like to give the electronic 12 Volt and the Heatbed + Stepperdrivers (1/128) 24 Volt.
(So it is possible for no extra cooling fan for Electronic needed+1/128 RRD Silencioso a large alu-cooling so also no cooling need for Nema17 since 2A)
As Result I have a stabe (Without USB-Cable and seperate CPU`s, RADDS stable since 15 Ampaire and no cooling Problems ...),
Flexible, nearly Loudness (only PowerSupplyFan, Fan for Filamentcooling, mechanical nois for my Living-Room space (Wife-Problem-Workaround ;-))),
very soft,smooth printing (1/128) and Modular Electronic Solution.This Electronic-Setup is nearly enough for great Printresults.
It is only for my Individual Setup. The Advance with an Modular Electronic way is, that everyone can assamble his own Electronic as they need.
Disadvantage is, that is more complicated to Install and assamble it. So more for the advanced reprapers and not so for beginners (without manual, help, etc..).
RAMPS-FD can also nearly make it for my Setup if it is work.
It was design for Bobc (theoreticaly it can not be a bad electronic:-)) And for this that was interesst me.
@jaguarking11 Thank you for this Advice. I have not knowing it for a maybe a 3rd possibility.
I have buy the smart ramps for testing it. It Is generally not so Important for my Setup (5 Motors, only 1 controlled Fan out etc...).
But maybe I can have other expiriance with it.
If it is ok, I will give an Impression - Topic of it.
If it is not ok I will not post any comments/Topics ;-)
(Maybe to Hot, so fancooling is a must have :-(,
maybe max. 10Ampaire,
maybe bad slodered -> fast broken components,
maybe not compatible with Firmware,
maybe unstable etc...).
Nobody, that give me an assambled, newer RAMPS-FD Version for Testing it (also we can change RAMPS-FD with RADDS++Components).
Have Fun and thank you
Angelo
I like to test Bobc `s RAMPS-FD.
With the cool securityfeatures (thank you Cefiar) and maybe an EEPROM on board
(I have heared that it is an EEPROM now on the newer RAMPS-FD, right ?).
That can be Important for my target electronic-Setup.
@dc42 Duett, Azteeg X5 mini 32BIT All-in-one Controller and Smoothieboard are, so I think, very cool Boards, but for personaly for me not so Important.
First I would like to work with Repetier-firmware (v 0.92 now realy stable with Due and 1/128) because repetier is a friend of my and so I have so a PREMIUM SUPPORT :-).
At Least I will run also my Printes with a UDOO Quad board (not with a Arduino Due).
Then I will run with 1/128 Microstepper and 2-3 Hotend-extruders and one silence permanent fan for the Metall Hotend and a second for individual Filamentcooling.
Also I am a friend, that I like to give the electronic 12 Volt and the Heatbed + Stepperdrivers (1/128) 24 Volt.
(So it is possible for no extra cooling fan for Electronic needed+1/128 RRD Silencioso a large alu-cooling so also no cooling need for Nema17 since 2A)
As Result I have a stabe (Without USB-Cable and seperate CPU`s, RADDS stable since 15 Ampaire and no cooling Problems ...),
Flexible, nearly Loudness (only PowerSupplyFan, Fan for Filamentcooling, mechanical nois for my Living-Room space (Wife-Problem-Workaround ;-))),
very soft,smooth printing (1/128) and Modular Electronic Solution.This Electronic-Setup is nearly enough for great Printresults.
It is only for my Individual Setup. The Advance with an Modular Electronic way is, that everyone can assamble his own Electronic as they need.
Disadvantage is, that is more complicated to Install and assamble it. So more for the advanced reprapers and not so for beginners (without manual, help, etc..).
RAMPS-FD can also nearly make it for my Setup if it is work.
It was design for Bobc (theoreticaly it can not be a bad electronic:-)) And for this that was interesst me.
@jaguarking11 Thank you for this Advice. I have not knowing it for a maybe a 3rd possibility.
I have buy the smart ramps for testing it. It Is generally not so Important for my Setup (5 Motors, only 1 controlled Fan out etc...).
But maybe I can have other expiriance with it.
If it is ok, I will give an Impression - Topic of it.
If it is not ok I will not post any comments/Topics ;-)
(Maybe to Hot, so fancooling is a must have :-(,
maybe max. 10Ampaire,
maybe bad slodered -> fast broken components,
maybe not compatible with Firmware,
maybe unstable etc...).
Nobody, that give me an assambled, newer RAMPS-FD Version for Testing it (also we can change RAMPS-FD with RADDS++Components).
Have Fun and thank you
Angelo