Duet and Simplify3D
I've finally got Simplify3D running, I like it a lot. I'm wondering if it will work with the Duet+Duex hardware running RepRap firmware? My Duet is still sat in its box waiting for something to put it...
View ArticleRe: ATX PSU, Heated Bed, and Wiring
Your options are to either use all the +12v (yellow cables) and all the Ground (Black cables in paralel) or simply cut them very short and solder them as a bunch on a much thicker cable to feed the...
View ArticleRe: ATX PSU, Heated Bed, and Wiring
You can run multiple wires to share the current. Presuming the supply and ground are the same gauge, you'll need just as many ground wires as supply. A single larger gauge wire may be easier to route...
View ArticleRe: RADDS RepRap Arduino-Due Driver Shield (32bit)
I'd definitely like to try this. I have a ramps-fd v1 and cant find a v2. Having trouble with the bobc's marlin for due and repetier (which both supposedly support ramps-fd). Any luck on this? I'd...
View ArticleRe: ATX PSU, Heated Bed, and Wiring
Quotecdru You can run multiple wires to share the current. Presuming the supply and ground are the same gauge, you'll need just as many ground wires as supply. A single larger gauge wire may be easier...
View ArticleRe: ATX PSU, Heated Bed, and Wiring
Quotetwicx So from what I can tell, the plan is to take 3 x 12V wires and 3 x GND wires from the ATX and "group" them so that they all connect to the HB + and GND respectively. Then take a single +12V...
View ArticleRe: Duet and Simplify3D
what firmware does the duet run? If it's standard Marlin or Repetier, it'll work
View ArticleRe: ATX PSU, Heated Bed, and Wiring
Quotecdru Quotetwicx So from what I can tell, the plan is to take 3 x 12V wires and 3 x GND wires from the ATX and "group" them so that they all connect to the HB + and GND respectively. Then take a...
View ArticleRe: Duet and Simplify3D
The Duet with RepRapFirmware emulates Marlin, but not perfectly. Most people with the Duet use the web interface to control it, because it provides more information and control than any of the USB...
View ArticleRe: RADDS RepRap Arduino-Due Driver Shield (32bit)
Quotevreihen Meh. Great if you want to use RepRapFirmware with no Delta printer support, but a paperweight for the people who need 32-bit CPU performance the most (Delta printer owners). Someone could...
View ArticleRe: Duet and Simplify3D
Excellent, this works for me. As an aside, do any printers ship with duet? I'd love to see more due based boards in circulation.
View ArticleRe: ATX PSU, Heated Bed, and Wiring
A few notes: 1. If you connect your heated bed sections in parallel, they will take 14A each at 12V (perhaps a little less after voltage drop in the wiring). That's 56A total, close to the limit of...
View ArticleClik here to view.
Re: ATX PSU, Heated Bed, and Wiring
Quotedc42 A few notes: 1. If you connect your heated bed sections in parallel, they will take 14A each at 12V (perhaps a little less after voltage drop in the wiring). That's 56A total, close to the...
View ArticleRe: ATX PSU, Heated Bed, and Wiring
Quotetwicx 2. This one has 2, but from each +12V contact point on the board, there's about 6 x 18AWG wires coming from it. So I'm assuming that if I'm grouping 3 x +12V and 3 x GND for the heat bed,...
View ArticleRe: ATX PSU, Heated Bed, and Wiring
Quotecdru Quotetwicx 2. This one has 2, but from each +12V contact point on the board, there's about 6 x 18AWG wires coming from it. So I'm assuming that if I'm grouping 3 x +12V and 3 x GND for the...
View ArticleRe: ATX PSU, Heated Bed, and Wiring
14A for the entire bed is much more reasonable. Unless you want the 200mm wide stuff, Amazon should be able to supply you with Kapton tape in a day or two.
View ArticleSwitching heat bed
Hi, I have old rapman 3.1 for which I build heated bed. The firmware allow to connect the heat bed to I/O of extruder 3. I have beed alble to connect the thermistor and the temperature measuring is...
View ArticleRe: Switching heat bed
Yes. One transistor can drive another although you may find it easier to integrate a solid state relay which is essentially the same thing in a tidy package.
View ArticleRe: 12864 Smart LCD with RAMPS 1.4 Strange behavior. :S
My friend ordered lcd for himself, so i think i will wait when he receives it and will check with other one. Maybe its not my board, maybe its the lcd itself thats cousing the problems?
View Article