Re: RADDS v1.2 und RAPS128 are arived
I would like to try this. Would you please PM me for details?
View ArticleRe: RADDS v1.2 und RAPS128 are arived
Gibt es bereits eine möglichkeit das Board zu erwerben?
View ArticleRe: is RADDS not open source?
If you would make a RADDS only for you, you can make it. Please contact me for this, if you like. Creative Commons 3.0 License is only, that you can not make it commercial ... For this we have the...
View ArticleNema 17 Connectors
Dear community, What I need to buy are the plugs that are used with the Nema 17 stepper motors. It reads in the description, that most of the stepper motors have "S6B-PH-K" build in. But after...
View ArticleRe: Nema 17 Connectors
QuoteIkiwi Dear community, What I need to buy are the plugs that are used with the Nema 17 stepper motors. It reads in the description, that most of the stepper motors have "S6B-PH-K" build in. But...
View ArticleRe: Nema 17 Connectors
"NEMA 17" is just a description of the bolt pattern dimensions. There isn't any specification that say what the wire lead connector to the motor needs to be, but they are often a connector make by JST...
View ArticleRe: Nema 17 Connectors
Thank you both! I will try this type of connector, @cdru: Yes this is true, but i have seen a lot of thouse connectors on nema 17 so i thought it will be good to mention it. Of coures this is not a...
View ArticleRe: Nema 17 Connectors
QuoteIkiwi Thank you both! I will try this type of connector, @cdru: Yes this is true, but i have seen a lot of thouse connectors on nema 17 so i thought it will be good to mention it. Of coures this...
View ArticleRe: Hot end suddenly not heating up
I checked the terminals and everything is well connected. I don't know how to check if the RAMPS MOSFET has blown - can anyone advise on that? The lights come on when I send the signal to the board to...
View ArticleRe: Hot end suddenly not heating up
If the LED on the RAMPS board lights up, the mosfet is at least passing minimal current. Take the mosfet out of the equation, just hold the ground from the hot end to the power supply ground. If it...
View ArticleRe: Printrboard Help
most are vary wary and will not follow a random YouTube link without a description
View ArticleTB6560 Single Axis 3A Stepper Driver
I bought 3 of these: [www.ebay.com] I intend to use them with Arduino Mega2560 + RAMPS 1.4 + Marlin. Are there other issues than getting 24V Power supply for these and increasing the Marlin's timing?...
View ArticleRe: TB6560 Single Axis 3A Stepper Driver
Oh and i realize, these in itself will need a fan, most using that chip has way larger heatsinks. Or maybe i'll just replace with a old huge CPU cooler ;)
View ArticleRe: is RADDS not open source?
Quotecdru Open Source does not mean that the PCB files have to be available, or even just a circuit board diagram and layout. The schematic is here if you didn't find it already. Duplicate the...
View ArticleUsing the full graphic smart controller outside of 3d printing, without the...
I'd like to find out the correct pins to use for the u8g library, so that I can use my display, buzzer and encoder in other Arduino Sketches.... I understand the programming aspect, but I'm really...
View ArticleRe: Using the full graphic smart controller outside of 3d printing, without...
I've used 12864 displays, but not with u8glib. According to [mssystems.emscom.net], the pin numbers you pass to u8glib need to be connected to the EN, RW and RS pins of the 12864 display in that...
View Articledrv8825 operating voltage vs a4988
Anybody with experience of using the drv8825 outside of a ramps/reprap setup? I have a stepper driver board to drive micro steppers running at 6v . The stepstick work seamlessly but i had some drv8825...
View ArticleRe: drv8825 operating voltage vs a4988
Yes, that could well be an issue. I advise against running either board at below its minimum rated voltage, because the chips in those boards need that minimum voltage to guarantee correct operatio...
View Article