Re: Xmega based design?
Do you think it would suffice with the 64-pin A3U or 44-pin A4U? No sdram support but simpler HW.
View ArticleRe: Megatronics 2.0 -> Connect servo for z-axis probing
Maybe its a bit late to answer but I did it on my megatronics board. use pin 46 (I forget the AUX number, you'll find it on the schematic) and you 'll need to define the servo pin in pins.h something...
View ArticleRe: Sanguish development
I have a few more Sanguish 1.1 kits available from the current batch. I'm trying out the Emakershop.com website so they will be sold through that website. Link to emakershop listing
View ArticleClik here to view.
Re: Megatronics 2.0 -> Connect servo for z-axis probing
Hi Rigor, thanks for you reply! I GOT IT WORKING! And thanks for the warning about the 5V bridge, I removed it before testing! Here are some details - for all who wish to add the automatic leveling by...
View ArticleRe: Megatronics v3 and Stepstick A4988 problem
Normally the A4988 have some protection which should help to avoid killing them... but anyhow: The easiest way to check if something is broken... change one hardware piece at a time and test again....
View ArticleRe: Dual extrusion TB6560 controller
Found it! And none of the suggestions helped. It drove me quite crazy. And then I discovered somebody else with similar problems: [giantpong.wordpress.com]. And it gave me a clue. But what caused it?...
View ArticleRe: Sanguish development
Found something interesting! Remember my TB6560AHQ trouble? None of the suggestions helped. It drove me quite crazy. And then I discovered somebody else with similar problems:...
View ArticleRe: Sanguish development
Nice catch! I'll have to put that up on the troubleshooting page for Sanguish as soon as I get around to making one. :)
View ArticleRe: Sanguish development
Then I also have another tip for all the users with trouble out there: check the sockets you are using to mount the TB6560AHQ's. It is very likely that the sockets don't make proper contact with the...
View ArticleRe: Sanguish development
To make it a little easier, these sockets work perfect and are more reliable: [www.sparkfun.com] (wich you can also find on eBay cheaper...)
View ArticleRe: RAMPS for BeagleBone
The design is so far working mostly as expected. I'm posting updates to the reprap wiki page, and will try to get a video uploaded soon. The only thing not really working as expected is the thermistor...
View ArticleRe: RAMPS for Due!
Bob and other contribs. Thanks for taking the time to design ramps-fd. Here is a pic with a print. I used latest repetier firmware and I can't detect any missing steps in this 1 hour print. Looking...
View ArticleAnyone own a working Panelolu2 for Sanguinololu who can help?
Hi guys, I just built a panelolu2 and am looking for some help with the solder jumpers. If someone has a working board, could they tell me how the jumpers are set on their board and which firmware...
View ArticleRe: Anyone own a working Panelolu2 for Sanguinololu who can help?
Maybe should have said, a photo would be nice :)
View ArticleRe: RAMPS for Due!
Really great work Bob, can't wait to get my hands on one when youve tested the latest version. I have a quick question though, I looked at your stuff on GitHub and you have .brd files but they don't...
View ArticleRe: RAMPS for Due!
QuoteJNOD I have a quick question though, I looked at your stuff on GitHub and you have .brd files but they don't open in eagle. What software do you need to view your files? I am after a BOM to see...
View ArticleHilfe Slave defekt automatisch Master kaput
Hallo ich habe eine großes Problem und hoffe dass mit jemand Helfen kann Ich hab einen Tricolor Mendel mit der Firmware Marlin 1.0.5RRP nun bekomme ich keine Verbindung mehr zum der Slave Platine Da...
View ArticleMegatronics v3 (DRV8825) stepper won't move anymore
First my printer was runnig well, but on the next day I've aborted a print some seconds after it has began to run. So now I have a big problem i cant' solve. I've uploaded the testsoftware to the...
View ArticleRe: Anyone own a working Panelolu2 for Sanguinololu who can help?
HI Jnod Please check out the blog post here: [blog.think3dprint3d.com] for an overview of the circuit and the use of the jumpers. this blog post has a picture showing how the jumpers are to be set to...
View Article