Re: Unusual stepper ratings - vref settings for new Melzi
Sry for your hotend. As it leaked before, thats where it was leaking from, most probably through a fissure at that place. Supposedly the nozzle was clogged or the filament was too hard to push and...
View ArticleRe: RAMPS for Due!
Quotecdsteinkuehler Quotesakunamary GOOOOOOD JOB！！！cdsteinkuehler ， but I do not know about the BBB...... raspberry , PCduino .BBB ,i can't tell which is better.... Well, for machine control I would...
View ArticleWhere are the Azteeg X3 v1.2 gerber files?
Hey, I'm trying for the past 2 days to find Azteeg X3 gerber files for the latest version without any luck. Isn't it open source project? Where can I find latest version (v1.2) gerber files, BOM,...
View Articlenew RADDS v1.1 arived (32-bit RepRap Arduino-Due Driver Shield)
Hello community, have now again RADDS v1.1 for 49,90 EUR (while stocks last). Willy gets (the inventor and quality inspectors) 5 Euro per sold RAMPS shield. Bolt receives (who built the firmware and...
View ArticleRe: Servos to Rambo 1.2 d
just put the orange signal wire from the servo on pin 6 of the EXT1 header. Pin 1 is +5V Pin 2 is ground. in the pins.h file, you need to define the pin, under the 301 motherboard section. #define...
View ArticleRe: Where are the Azteeg X3 v1.2 gerber files?
Yes the guys took open source resources from the community, made a closed source product, and sell it to the otherwise open source community. Sadly there is much more than one case of that. Goes under...
View ArticleRe: Need some help for the cables.
QuoteBoByS Based on the formula, I think that 4mm^2 will be good enought, but I still need a help..RAMPS has 5 and 11amp fuses for the main electronics and heated bed respectively. 11 amps chassis...
View ArticleRe: DIY Power Supply?
Thanks everybody for taking the time to reply. This has been a good learning experience, even if just a thought exercise. I plan on using a pre-made switching power supply to build a 3D printer and...
View ArticleRe: Where are the Azteeg X3 v1.2 gerber files?
QuoteNoobMan But personally i think it must be because they are americans. Perhaps some among them may be ok, but otherwise as nation they tend to do exactly that... Do whatever they want - and invent...
View ArticleRe: Where are the Azteeg X3 v1.2 gerber files?
Totally agree with cdru. It has nothing to do with Americans etc.. I'm just wondering how come the whole community is fooled by thinking it's an open source design, the official RepRap wiki states the...
View ArticleRe: Where are the Azteeg X3 v1.2 gerber files?
Azteeg "never become closed source" because simply it was never open. Sources were never available not even from start. Its not a known issue, because these kinds of stuff(s) are based on ppls...
View ArticleRe: Where are the Azteeg X3 v1.2 gerber files?
QuotedeluzI'm just wondering how come the whole community is fooled by thinking it's an open source design, the official RepRap wiki states the same even with a licenses of "CC ShareAlike 3.0". Shall...
View ArticleRe: new RADDS v1.1 arived (32-bit RepRap Arduino-Due Driver Shield)
Hi Angelo, have you tried it on the Udoo? Can I use the 24v with the Udoo, like you say here "RADDS mit 24 V betreiben"? :)
View ArticleRe: new RADDS v1.1 arived (32-bit RepRap Arduino-Due Driver Shield)
yes you can use it, but you have to sold out the Diode D1. and then you have to sold 3 ten Diods (4 V und 1,3 Watt). Please have an atention for the diod direction fom left to right (down, up,down)....
View Articleissue of RAMPS-FD LCD adapter (with smart controller)
Hi all I am trying making a ramps-fd lcd adapter ,bobc give us a very nice solution ,in bobc's solution ,the adapter change the logic voltage with 74HC07A .I make some change ,I use 74LS07 and...
View ArticleRe: Where are the Azteeg X3 v1.2 gerber files?
Something like that was discussed already on this forum some time ago, which lead to the wiki mention. One guy having the board wanted more information and after digging a little around the issue it...
View ArticleRe: Need some help for the cables.
Wow, thank you very much for all of the interesting stuff in your answer. It's really clear now! Best regards, Bobby
View ArticleRe: Where are the Azteeg X3 v1.2 gerber files?
I searched and found the link for the previous discussion about sources, for further reference it was in this thread. Two posts down somebody else quoted the wiki addition which i thought to be...
View ArticleRe: RAMPS for Due!
This board is great, I love it so far! I've got mine at Getech, and am using it to drive my GUS Simpson, it is my first printer, and it is not printing yet - I am still testing, so RAMPS-FD is a test...
View ArticleRe: Where are the Azteeg X3 v1.2 gerber files?
Well, it's kinda a funny statement about time. It should be managed as any other open-source project, all sources exposed and other contribute.. even if the "gerber is messy".. Gotta say, RAMBo is...
View Article