Re: Unipolar Headaches: An Irritated newb
I can't find any stepper motors matching that model number in that booklet. There is a list of SST43D motors (rather than STP43D), but there is no 1006 model of those listed either. I did find them...
View ArticleRe: Unipolar Headaches: An Irritated newb
The labels, where I'm taking the motor information from, might be cataloged according to the people who assembled the kit (DIYtechshop); So I'm not sure if following the part number is the same-same....
View ArticleRe: Unipolar Headaches: An Irritated newb
Oh snap.... yeah.. so i probably have 2 issues... First, the Firmware has a max acceleration of 3000 mm/s2, which would mean, per second squared the motors would be trying to move at least 3 meter.......
View ArticleRe: Which electronics is best for the E6D kraken
Any idea when the next version is? Apart from adding one to my ormerod, I am now looking at what electronics to use for a Kossels with multi tool heads (like à kraken or true RGBK head we are trying...
View ArticleEndstop wiring?
I am almost there with my printer build but my endstops are not registering. I run a test print of a cube bypassing the home command in the gcode and that runs fine I purchased the electronics kit...
View ArticleRe: Firmware to drive X-Y galvanometer
hey vicktor I'm finally trying to buy a galvo system. so, can you help me please? okay if you search"40kpps galvo" at ebay, some galvos are there which i'm trying to purhcase. um... so please make me...
View ArticleRe: Which electronics is best for the E6D kraken
I can't give a time line on the next version yet i'm afraid. Regards Tony
View ArticleRe: Firmware to drive X-Y galvanometer
... I've only tested the chinese galvos for comparison and playing with the idea of a cheap system -- so no real experience with types or vendors ... my other galvos are from comercial systems. For...
View ArticleRe: Unipolar Headaches: An Irritated newb
30 for the acceleration should be no problem. I use 800 on my Ormerod for X and Y, which does about 87 steps/mm. The Z and the E need to be lower because they have more steps/mm.
View ArticleRe: Firmware to drive X-Y galvanometer
hey vicktorrrr cna i use 405nm 20mw blue laser [www.ebay.com] at this? [www.ebay.com]
View ArticleRe: Firmware to drive X-Y galvanometer
Quotegeniouskotaro hey vicktorrrr cna i use 405nm 20mw blue laser [www.ebay.com] at this? [www.ebay.com] i'm going to use at sla printer, so is the laser strong enough to cure the uv resin using a...
View ArticleClik here to view.
Question voltage regulator
Hey my friend and I are working on our Ormerod 2 and were checking the Voltage Regulator with our multimeter. We have strange results, and we hope you can make us a bit smarter. Here's a picture of...
View ArticleRe: Controller LCD contrast issue
drhender, I have same LCD like you (without 3K resistor). Siple to fix - put 1K resistor into two pins
View ArticleRe: Endstop wiring?
Thanks for the info but that doesn't really tell me what wire goes where on the switch or the board (Ramps 1.4).
View ArticleRe: Firmware to drive X-Y galvanometer
... no, this diode is not strong enough and with a very bad beam profile, so the focus shape in distances bigger than 100mm will result in a distortet oval, not in a spot! - this 405nm-diodes can be...
View ArticleRe: New TFT control panel for 3D printers
Update: The kit is available for pre-order, please see this post: [forums.reprap.org]
View ArticleRe: Question voltage regulator
The voltage regulator is sitting between B & D and is trying to regulate the voltage on the output, from the Input to the Output. A & C are simply the common ground. I'm suprised there aren't...
View ArticleRe: Endstop wiring?
Have you looked at the diagram on page 103 of the manual, and if so, what is it about that diagram that you don't understand?
View Article