Re: Endstop wiring?
It all up and running now.:) Should have really calibrated the printer first before printing a 20mm test cube....... but at least it resembles a cube.:p Cheers guys.
View ArticleRe: Endstop wiring?
Quotedc42 Have you looked at the diagram on page 103 of the manual, and if so, what is it about that diagram that you don't understand? It was the wire colouring that was throwing me off.
View Article128x64 GLCD Connected to Printrboard Rev D?
I'm trying to find a way to connect my "Full Graphic Smart Controller Graphical LCD (128x64) Screen" to my Printrbot 1405, so I can control it via the rotary encoder, and use the SD Card of the Smart...
View ArticleWiring 3d printer fan
Hi guys, I have quite a problem with my LeapFrog 3d printer in replacing the 2 cooling fan (25mm). The connector seem quite strange, I think it might be a JST one. Finding them in online stores is...
View ArticleRe: Wiring 3d printer fan
Are you referring to an JST connector perhaps? I need to replace a fan and I am looking for instructions on how to disconnect without distroying the 6-lead JST socket on my Ormerod2. Anyone who knows...
View ArticleRe: Wiring 3d printer fan
Quoteefraimalexander Are you referring to an JST connector perhaps? Yes I am thank you! I will upload picture as soon as I can.
View ArticleRe: Wiring 3d printer fan
It's interesting. I have only had the Ormerod 2 since this autumn and I have only consumed one roll of PLA. The extruder has been at 200 C at top and still the fan appears fried. It was always very...
View ArticleRADDS v1.2 + UDOO = not enough power from 12V
Is there anyone here with a RADDS v1.2 shield and UDOO that has been able to successfully power both from the 12V VIN on the RADDS? It works fine if the UDOO is plugged into 9V and the RADDS is...
View ArticleRe: Alternative to RAMPS 1.4 for DELTA printer? Smoothieboard maybe? is there...
QuoteNoobMan If you fancy DIY, then this may be an option. You have to draw wiring, but will work with any development board of any kind :) Sort of breadboard style. DIY is not easy！
View ArticleRe: Controller LCD contrast issue
I have a similar but not quite the same issue here [forums.reprap.org] and I have a slightly different board too, so although the resistor ideas may still work, I'm not sure where I would try putting...
View ArticleRe: Alternative to RAMPS 1.4 for DELTA printer? Smoothieboard maybe? is there...
Does smoothieware have servo support now? Haven't been following since the early sw dev days (still have the early beta board, in fact).
View ArticleClik here to view.
Re: Controller LCD contrast issue
I have checked how the trimpot and my additional resistor are connected to the 20x1 pin row which is also present on your board. I tried to draw it on top of your photo: This is just how the resistors...
View ArticleRe: Controller LCD contrast issue
Yes perfect, thank you enif! For me a 2k2 resistor between GND and Contrast has fixed the issue! :) Same here.. the Marlin contrast setting has no effect.
View ArticleRe: Alternative to RAMPS 1.4 for DELTA printer? Smoothieboard maybe? is there...
Quotevreihen I am looking forward to seeing Delta support in RepRapFirmware on the Duet. The lack of Delta support is the only reason why I did not buy a Duet board months ago..... I have written blog...
View ArticleRe: Alternative to RAMPS 1.4 for DELTA printer? Smoothieboard maybe? is there...
I use for Deltas our RADDS v1.2 with RAPS128 Solution with Repetier-Firmware v 0.92 Stable-and flexible-Firmware, very accurate and low vibrations-> better printresult->low noise ...:...
View ArticleRe: Alternative to RAMPS 1.4 for DELTA printer? Smoothieboard maybe? is there...
Angelo Do you still do/have the large round Heatbed for a Delta I seem to remember a post some time back ref a 400mm diameter one that you were doing if so can you give me a price for one please? Doug.
View Articleamperage to hotend
Hi folks, I know this has probably been answered elsewhere buy I have been unable to locate. What is the typical amps that are needed to run a hotend at ABS temps? Just curious because I want to tweak...
View ArticleRe: Alternative to RAMPS 1.4 for DELTA printer? Smoothieboard maybe? is there...
HI doug, how are you, fine to read you? Work your KRAKEN solution with RADDS+Extension ? [e3d-online.com] It works fine, or you need help (firmware etc...) ? Can you post some Fotos please? Yes, I...
View ArticleRe: Alternative to RAMPS 1.4 for DELTA printer? Smoothieboard maybe? is there...
Angelo No not made any progress with the CoreXY and Radds yet been to busy and keep redesigning it as I am not to happy with bits and think I may do it again to use V-Groove Wheels on Makerslide for...
View Article