Re: RAMPS for Due!
Quotekarabas If head path is very complicated and speed is high the gcode comand rate is too high and 250000(standart Ultimaker rate) is not enough. So native USB is a must. Yes? I haven't had a...
View ArticleRe: RAMPS for Due!
@karabas You should also be aware that the baud rate may not actually be the limiting factor, rather, the planning calculations may be. This is much more likely on AVR boards (you were experiencing...
View ArticleRe: RAMPS for Due!
You have a *lot* of ram on the ARM parts. They also are pretty good at things like DMA to / from RAM for serial i/o. I suspect that a fairly big serial buffer would take care of any possible serial...
View ArticleRe: Sanguish development
In some libraries the mounting tabs on the USB go into unplayed holes. Yes I know that's stupid. Libraries do stupid things sometimes. If you fix the USB, check the holes. They should be plated. I'm...
View ArticleRe: Dual extrusion TB6560 controller
I have made a few updates to the board: - The fuses are now in the positive line, this should improve safety. I have chosen to go for polyfuses, but I will test normal fuses in this design as well. -...
View ArticleRe: RAMPS for Due!
I got my ramps-fd from geeeteck... its going to need some work.. Quick review [dustsreprap.blogspot.co.nz]
View ArticleRe: RAMPS for Due!
QuoteDust Some of the pins are quite bent over. Its obvious this happened at the factory as the 4th pin from the right is far to low and has been soldered in like that! But otherwise the bending of...
View ArticleRe: RAMPS for Due!
Which Firmware is used für the RAMPS-FD? EDIT: Sorry found it (R2D2) [github.com] Have fun angelo
View ArticleRe: RAMPS for Due!
I will produce 100 Radds Shield for arduino due [www.dr-henschke.de] [forums.reprap.org] In 2 Weeks i have the first 5 Shield... If it is ok, since the end off dec. 2013 100 RADDS Shields. The...
View ArticleRe: RAMPS for Due!
Quoteangelo Which Firmware is used für the RAMPS-FD? Have fun angelo Reading though this forum turns up: - Bobc's port of R2C2 - APrinter (developed by me) - Perhaps some form of RepetierFirmware, see...
View ArticleRe: RAMPS for Due!
Hi Ambrop7, cool and thank you for this information. Maybe i will test R2D2 and aprinter for the RADDS Shield, and maybe the firmware ist better then Repetier? I think the 32bit more than overdue for...
View ArticleRe: RAMPS for Due!
Quoteangelo Maybe i will test R2D2 and aprinter for the RADDS Shield, and maybe the firmware ist better then Repetier? angelo I can't help you with R2D2, the port is being developed by bobc not me....
View ArticleRe: RAMPS for Due!
Hi ambrop7, do you have Interesst for a RADDS Shield to test it with your APrint Firmware? If yes, so PM me and i will send you one Shield for free, OK? Have Fun angelo
View ArticleRe: RAMPS for Due!
Quoteambrop7 Ok, I agree. Is it possible to port easely the code to discovery? I got this board an year ago by mistake... BTW did you read this thread? About new future ultimaker board [github.com]...
View ArticleRe: RAMPS for Due!
Quotekarabas Ok, I agree. Is it possible to port easely the code to discovery? I got this board an year ago by mistake... BTW did you read this thread? About new future ultimaker board [github.com]...
View ArticleRe: RAMPS for Due!
Repetier for due firmware https://github.com/biocode3D/Repetier-Firmware-Due I know it compiles.. but thats as far as ive gotten with it.
View ArticleRe: RAMPS for Due!
annother new board [www.reprappro.com] But its the same ARM processor as the Arduino Due, so its firmware [github.com] should be able to be ported esily to ramps-fd
View ArticleRe: RAMPS for Due!
QuoteDust Repetier for due firmware https://github.com/biocode3D/Repetier-Firmware-Due I know it compiles.. but thats as far as ive gotten with it. I don't have a fully working Repetier for RAMPS-FD...
View ArticleRe: RAMPS for Due!
QuoteDust annother new board [www.reprappro.com] But its the same ARM processor as the Arduino Due, so its firmware [github.com] should be able to be ported esily to ramps-fd I've given it a quick...
View Article